@article { author = {Khazaei, Masoud and Mehdi Nezhad Nori, Mohammad and Hasanzadeh, Mahdi and Rezaei, Mohammad}, title = {Synthesis of Porous Zirconium-based Metal-Organic Framework Nanostructure for Detoxification of Chemical Pollutants}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2452-2460}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.1}, abstract = {Due to the severe and harmful effects of chemical pollutants on human health and the environment, researchers have always been looking for effective ways for detoxification of chemical pollutants. In this study, zirconium-based metal-organic framework (UiO-66) nanostructures were synthesized in two gel-based (xerogel) and solvothermal (aerogel) methods. Morphology, crystalline structure, porosity and specific surface area as well as their behavior against degradation of dimethyl methylphosphonate (DMMP) as nerve agent simulant were evaluated by scanning electron microscopy (SEM), X-ray diffraction (XRD), N2 adsorption isotherms (BET) and gas chromatography-mass spectrometry (GC-MS). The results showed the synthesis of aerogel and xerogel UiO-66 with uniform size distribution and crystalline structure indicating the successful synthesis of these compounds. UiO-66 xerogel also showed higher specific surface area and pore volume than UiO-66 nanocrystals (aerogel). The degradation performance of the synthesized metal-organic framework nanostructures showed that the UiO-66 xerogel with a half-life of 28.6 min had better catalytic properties than the UiO-66 aerogel at 120 min and ambient temperature, as about 80% of DMMP is hydrolyzed.}, keywords = {Metal-organic framework,Specific surface area,dimethyl methylphosphonate,Hydrolysis}, title_fa = {سنتز نانوساختار متخلخل چارچوب آلی-فلزی بر پایه زیرکونیوم به منظور تخریب عوامل آلاینده شیمیایی}, abstract_fa = {محققان با توجه به آثار شدید و زیانبار عوامل شیمیایی بر سلامت انسان و محیط زیست، همواره بدنبال روش‌های موثر پاکسازی و رفع آلودگی بوده اند. در این پژوهش نانوساختارهای چارچوب آلی-فلزی برپایه زیرکونیوم (UiO-66) به دو روش ژل پایه (زیروژل) و حلالی-حرارتی (آئروژل) سنتز شد. مورفولوژی، ساختار کریستالی، خصوصیات تخلخل و سطح مخصوص و همچنین رفتار آنها در برابر تجزیه دی متیل متیل فسفونات (DMMP) به عنوان شبه عامل اعصاب با استفاده از میکروسکوپ الکترونی روبشی (SEM)، پراش پرتو ایکس (XRD)، ایزوترم جذب گاز نیتروژن (BET) و کروماتوگرافی گازی- طیف سنج جرمی (GC-MS) ارزیابی شد. نتایج بدست آمده نشان‌دهنده سنتز آئروژل و زیروژل UiO-66 با توزیع اندازه یکنواخت و ساختار کریستالی بوده است که بیانگر سنتز موفقیت‌آمیز ترکیبات مذکور می‌باشد. همچنین زیروژل UiO-66 سطح مخصوص و حجم حفرات بیشتری نسبت به نانوکریستال UiO-66 (آئروژل) نشان داد. بررسی‌های عملکرد رفع آلودگی نانوساختارهای چارچوب آلی-فلزی سنتز شده نشان داد که زیروژل UiO-66 با زمان نیمه عمر 6/28 دقیقه، خاصیت کاتالیستی بهتری در مقایسه با آئروژل UiO-66 داشته است، بطوریکه در مدت زمان 120 دقیقه و دمای محیط، حدود 80% از عامل آلاینده DMMP هیدرولیز شده است.}, keywords_fa = {چارچوب آلی-فلزی,سطح ویژه,دی متیل متیل فسفونات,هیدرولیز}, url = {https://amnc.aut.ac.ir/article_115567.html}, eprint = {https://amnc.aut.ac.ir/article_115567_984212e37940d101fbad7afa0ab83acf.pdf} } @article { author = {Maghazeii, Farnaz and Ghanbari, Davood}, title = {The Study of Nanostructure, Magnetic Properties and Photocatalytic Behavior of Fe3O4/Ag Nanocomposites Synthesized by Microwave Method}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2462-2473}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.2}, abstract = {We prepared samples including nanoparticles of Fe3O4 via co-precipitation method with microwave heating using water and ethylene glycol as solvent. The procedure was repeated with various natural surfactants. XRD and SEM analysis was performed to determine the nanostructural characteristics of nanoparticles. SEM analysis disclosed that the type of surfactant and solvent will affect the nanostructures. In the next stage, Fe3O4/Ag nanocomposite was prepared using magnetite nanoparticles and AgNO3 by microwave method and its nanostructure was defined by SEM and TEM analysis. The mean diameter was determined between 40-55 nm from SEM software and 44-64 nm by Motic software for particles of all samples. Likewise, the purity of Fe3O4 nanoparticles and prepared nanocomposite were documented by FT-IR spectrometry. All the products had pure nanoparticles of Ag and Fe3O4 which was agreed with XRD results. To evaluate the magnetic parameters of samples, VSM analysis were done. Hysteresis curves disclosed that all the products have superparamagnetic properties. We also assessed the photocatalytic potential of prepared nanocomposites using methyl orange and congo red solutions under UV radiation and the effect of concentration of absorbent, pH of solutions and the time of irradiation on the color removing was investigated. This study confirms that these Fe3O4/Ag nanocomposites can be used as recyclable photo-catalysts for water refinery in home and industries. The best result for color removing was for 0.9 gr/lit absorbent, pH=2 and t= 80 min for irradiation.}, keywords = {Fe3O4/Ag nanocomposite,Fe3O4 nanoparticles,Nano photo-catalyst,Nanostructure,Superparamagnetic}, title_fa = {بررسی نانوساختار، خواص مغناطیسی و رفتار فتوکاتالیستی نانوکامپوزیت های Fe3O4/Ag تهیه شده به روش مایکروویو}, abstract_fa = {نمونه‌های حاوی نانوذرات اکسیدآهن به روش هم‌رسوبی در مایکروویو با استفاده از آب و اتیلن گلیکول به عنوان حلال سنتز شدند. سنتز در حضور عوامل فعال‏کننده سطحی نشاسته، لاکتوز و سدیم دو دسیل سولفات ( SDS ) تکرار شد. تحلیل‏ با میکروسکوپ الکترونی روبشی( SEM )و پراش پرتو ایکس (XRD )جهت بررسی نانوساختار نمونه‌ها انجام شد. نتایج SEM نشان دادند که نوع حلال و عامل فعال‏کننده سطحی در خصوصیات نانوساختاری نمونه‌ها مؤثرند. در مرحله بعد با استفاده از نانوذرات اکسیدآهن تهیه شده و نیترات نقره، نانوکامپوزیت هسته-پوسته تهیه شد و نانوساختار آن با استفاده از تحلیل های SEM و میکروسکوپ الکترونی عبوری ( ( TEM مورد بررسی قرار گرفت. قطر میانگین نانوذرات در تمام نمونه ها توسط نرم‌افزار SEM در محدودهnm ۴۰-۵۵ و با دقت بیشتر به کمک نرم افزار Motic مابین nm ۴۴-۶۴ بدست آمد. طیف‌های تهیه شده توسط طیف سنج مادون قرمز تبدیل فوریه(FT-IR) برای نانوکامپوزیت و نمونه حاوی اکسیدآهن نیز نشان دادند که نمونه‌های تقریباً خالصی بدست آمده است. همچنین منحنی‌های هیسترزیس بدست آمده از مغناطیس سنج نمونه ارتعاشی ( VSM) نشان دادند که هر دو نمونه دارای خاصیت سوپر پارامغناطیسی هستند. در نهایت برای تأیید رفتار فتوکاتالیستی این نانوکامپوزیت، از دو محلول رنگی متیل اورنج و کنگورد حاوی نانوکامپوزیت تحت تابش پرتو فرابنفش استفاده شد و اثر مقدار ماده جاذب، pH محلول و مدت زمان پرتودهی روی درصد کاهش غلظت رنگ محلول‌ها مورد بررسی قرار گرفت که حدود ۹۰٪ کاهش غلظت رنگ برای مقدار جاذب gr/lit ۹/.، ۲=pH و مدت زمان تابش ۸۰ دقیقه بدست آمد.}, keywords_fa = {سوپرپارامغناطیس,نانوذرات اکسید آهن,نانو ساختار,نانو فتوکاتالیست,نانوکامپوزیت اکسید آهن/ نقره}, url = {https://amnc.aut.ac.ir/article_118633.html}, eprint = {https://amnc.aut.ac.ir/article_118633_9054fb25397f637abd9166f0a0e35cf9.pdf} } @article { author = {Latifi, Masoud and Bagherzadeh, Roohollah}, title = {Hybrid Pizo-Triboelectric Energy Nanogenerator from Woollen fabric and PVDF/BaTiO3 Nanofibrous Layer}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2474-2481}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.3}, abstract = {Harvesting of wasted energies using mechanical to electrical energy nanogenerators has become a major branch of energy research area due to the global energy concerns. Piezoelectric and triboelectric mechanisms are between the two most widely used methods in this field. In this study, different combinations of fibrous nanogenerators including PVDF nanofibers and PVDF / BaTiO3 composite nanofibers with wool fabrics consist of three types of weft knitted fabric and combed wool fibers were prepared, due to their promising position in the triboelectric series. Different configuration of layers were also set to optimize the layer composition for the best electrical output. The electrical output voltage per unit area of different samples were measured after the contact - separation mode of electrification for each sample. Results showed that the arc-shape layer deposition has the best triboelectric layer arrangement to achieve the optimized electrical output at a specified force with the highest output value of 4.35(V/cm2), where the output of PVDF piezoelectric layer was only 0.475(mV/cm2). For a given force, the output of the triboelectric nanogenerator was more than 9000 times higher than that of the pure PVDF/BaTiO3 piezoelectric nanogenerator. These results teach us a first step towards the fabrication of self-chargeable wearable microelectronic devices.}, keywords = {Energy harvesting,Piezoelectric,Triboelectric,Composite nanofibers,PVDF/BaTiO3 nanofibers}, title_fa = {مبدل انرژی هیبریدی تریبو-پیزوالکتریک از پارچه پشمی و لایه نانوالیاف PVDF/BaTiO3}, abstract_fa = {برداشت انرژی‌های هدر رفتنی با کمک مبدل‌های انرژی مکانیکی به الکتریکی با توجه به معضل جهانی انرژی، از جمله رویکردهای نوین در توسعه محصولات میکروالکترونیک مبتنی بر سازوکار پیزوالکتریک و تریبوالکتریک میباشد. در این مقاله ترکیب‌های مختلفی از مبدل‌های الیافی شامل نانوالیاف PVDF و نانوالیاف کامپوزیتی PVDF/BaTiO3 با لایه‌های پشمی با سه نوع بافت حلقوی پودی و الیاف پشم شانه‌شده، باتوجه به جایگاه مناسب ماده پشم و PVDF در گروه مواد تریبوالکتریک، در نظر گرفته‌ شد. میزان ولتاژ الکتریکی خروجی حاصل از تماس- جدایش تریبوالکتریک بر واحد سطح مبدل جهت ارزیابی خواص نمونه‌های تولید شده و مقایسه آنها با مبدل‌های تک‌لایه اندازه‌گیری شد. همچنین نحوه‌ی چیدمان بهینه لایه‌ها مورد ارزیابی قرار گرفت. نتایج حاصل از بررسی‌ها نشان داد که بهترین چیدمان لایه‌ای تریبوالکتریک در یک نیروی مشخص با ساختار کمان‌شکل حاصل شده و مقدار بالاترین خروجی (V/cm2)35/4 قابل دسترس میباشد. در حالی که خروجی لایه‌ی پیزوالکتریکPVDF به‌تنهایی در بهترین لایه‌ی ترکیبی آزمایش‌‌شده در نمونه‌های تریبوالکتریک به‌مقدار(mV/cm2) 475/0 میباشد. بر اساس نتایج بدست آمده، ساخت مبدل‌ها به صورت هیبریدی با ساختار معرفی شده در این پژوهش می‌تواند در ازای اعمال نیروی یکسان، خروجی مبدل تریبوالکتریک را نسبت به لایه‌ی مبدل پیزوالکتریک PVDF/BaTiO3، بیش از 9000 برابر افزایش دهد. ساختار معرفی شده می تواند به عنوان گامی موثر در راستای توسعه مواد پیشرفته برای توسعه محصولات میکروالکترونیک خودشارژشونده و قابل پوشیده شدن مورد استفاده قرار گیرد.}, keywords_fa = {مبدل های انرژی,پیزوالکتریک,تریبوالکتریک,نانوالیاف کامپوزیتی,نانوالیاف PVDF/BaTiO3}, url = {https://amnc.aut.ac.ir/article_118634.html}, eprint = {https://amnc.aut.ac.ir/article_118634_8558612f870a321088e13aba7fdc136f.pdf} } @article { author = {Momeni, Mohamad Mohsen and Ghayeb, Yousef and Barati, Zahra}, title = {Preparation of tungsten-modified hematite-based photoconductors for photoelectrochemical cathodic protection of stainless steel}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2482-2489}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.4}, abstract = {Cathodic protection by using photocatalysts, a new method of metal protection, is known as photoelectrochemical cathodic protection. In this study, at first, hematite nanotubes were prepared by electrochemical anodizing method; and then, using chemical bath deposition method at different times, tungsten trioxide particles were created on the surface of hematite nanotubes. Electron microscopy images confirmed the formation of regular hematite nanotubes on the surface; so by increasing the deposition time, the nanotubes diameter reduced from 40 nm to about 36 nm. The results of XRD, EDX and EDX-Mapping showed the presence of tungsten particles and their uniform distribution on the surface of the nanotubes. In order to study the photoelectrochemical properties of the samples, as photoanode in the photoelectrochemical protection of 403 stainless steel, chronoamprometry, open circuit potential and Tafel methods were used. The results showed that the coated (modified) samples had better performance than the uncoated ones (bare nanotubes), and of all prepared samples, sample T3 (with a deposition time of three hours) has the best performance. Also, the calculation of electron half-life in the samples using OCP tests showed that this value for H, T1, T2 and T3 samples is 0.92, 1.96, 2.12 and 1.99 seconds, respectively.}, keywords = {Hematite,Tungsten trioxide,Photoelectrochemical cathode protection,Stainless steel}, title_fa = {تهیه فوتوآندهای برپایه هماتیت اصلاح شده با تنگستن برای حفاظت کاتدی فوتوالکتروشیمیایی فولاد ضدزنگ}, abstract_fa = {حفاظت کاتدی با استفاده از فوتوکاتالیستها، روش جدیدی از محافظت فلزات است که به حفاظت کاتدی فوتوالکتروشیمیایی مشهور است. در این پژوهش، در ابتدا نانولوله‌های هماتیت به روش آندایزینگ الکتروشیمیایی تهیه ‌شد و سپس با استفاده از روش رسوب ‌شیمیایی‌ حمامی در زمان‌های مختلف، ذرات تنگستن تری اکسید بر ‌روی سطح نانولوله‌های هماتیت ایجاد شد. تصاویر میکروسکوپ الکترونی، تشکیل نانولوله های منظم هماتیت را بر روی سطح تائید کرد به گونه ای که افزایش زمان رسوب‌دهی، باعث کاهش قطر دهانه نانولوله ها از 40 نانومتر به حدود 36 نانومتر شد. نتایج آزمونهای XRD و EDX-Mapping حضور ذرات تنگستن و توزیع یکنواخت آن بر روی سطح نانولوله ها را نشان داد. برای بررسی خاصیت فوتوالکتروشیمیایی نمونه‌ها، به عنوان فوتوآند در حفاظت فوتوالکتروشیمیایی فولاد ضدزنگ 403، از روش‌های کرونوآمپرومتری، پتانسیل مدار باز و روش تافل استفاده شد. نتایج نشان داد که نمونه‌های پوشش داده شده از عملکرد بهتری در مقایسه با نمونه‌های فاقد پوشش برخوردار بوده و از بین همه نمونه ها، نمونه ‌T3 (با زمان رسوب‌دهی سه ساعت) بهترین عملکرد را دارد. همچنین محاسبه نیمه عمر الکترون‌ در نمونه‌ها با استفاده از نمودارهای OCP نشان داد که این مقدار برای نمونه های H، T1، T2 و T3 به‌ترتیب برابر است با 92/0، 96/1، 12/2، 99/1 ثانیه.}, keywords_fa = {هماتیت,تنگستن تری اکسید,حفاظت کاتدی فوتوالکتروشیمیایی,فولاد ضد‌زنگ}, url = {https://amnc.aut.ac.ir/article_118635.html}, eprint = {https://amnc.aut.ac.ir/article_118635_729a64fa89b1c50008f5e8f41299bdcd.pdf} } @article { author = {Farrokhi, Mohammad and Zaarei, Davood}, title = {Self-Stratifying Metallic Coating Formulation Based on Polyurethane using Taguchi Experimental Design Method}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2490-2500}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.5}, abstract = {Abstract: In this study, self-stratified metallic surface coating based on polyurethane resin consisting of single-layer polymer acrylic with high gloss, without the use of clear coat, with the aim of covering industrial parts, home appliances and even car body repair was designed and formulated. The purpose of the work was to reduce the amount of consumables, work error and coverage time compared to the conventional and traditional coating (two layers of coating consisting of metallic base coat and clear coat). To design the experiments (DOE), the Taguchi method was used to optimize the type and amount of the main raw materials, including polyol acrylic resin type, cellulose acetate butyrate and wax. Various tests such as adhesion, gloss, hardness, abrasion salt fog and immersion were performed on the formulated coatings. The results showed, for example, an optimal adhesion rate of (5B), a gloss about 89%, mottling level of 51, and hardness of 210 seconds. Also, no sedimentation was observed in the liquid state and the results of moisture resistance and water immersion tests were acceptable based on standard criteria, compared to conventional double-layered samples.}, keywords = {Self-stratifying,metallic paint,Acrylic-polyol,Wax,cellulose-acetate-butyrate}, title_fa = {فرمولاسیون پوشش متالیک خود لایه شونده بر پایه پلی‌یورتان با بهره گیری از روش طراحی آزمایش تاگوچی}, abstract_fa = {در این پژوهش، پوشرنگ رویه متالیک از نوع خود لایه شونده بر پایه رزین پلی‌یورتان متشکل از پلی ال اکریلیک بصورت تک لایه و با براقیت بالا، بدون استفاده از لایه لاک بیرنگ (لایه شفاف فاقد رنگدانه)، با هدف پوشش دهی قطعات صنعتی و لوازم خانگی و بعضا تعمیر بدنه خودرو بالانس و طراحی شد. هدف از انجام کار، کاهش میزان مواد مصرفی، خطای کار و زمان پوشش دهی نسبت به حالت مرسوم و سنتی(بصورت دو لایه پوشش متشکل از پوشش میانی متالیک و یک لاک بیرنگ شفاف) بوده است. برای طراحی آزمونها (DOE) از روش تاگوچی جهت بهینه یابی نوع و مقدار مواد اولیه اصلی تاثیرگذار بر پوشش اعم از نوع رزین آکریلیک پلی ال، سلولز یوتیرات استات و وکس استفاده شد. آزمونهای مختلف نظیر چسبندگی، براقیت، سختی، میزان ابلقی شدن، مه نمک، غوطه وری بر روی پوشرنگهای بهینه شده انجام شد. نتایج برای نمونه بهینه نشان دهنده میزان چسبندگی درجه (5B)، براقیت در حدود 89 درصد، میزان ابلقی شدن در سطح 51 و سختی در حد 210 ثانیه با مقیاس پرسوز بود. همچنین هیچ گونه رسوب و ته نشینی در حالت مایع مشاهده نشد و نتایج آزمونهای مقاومت در برابر رطوبت و غوطه وری در آب، بر اساس معیارهای استاندارد در قیاس با نمونه های دولایه مرسوم، قابل قبول و تایید بودند.}, keywords_fa = {خود لایه شونده,پوشرنگ متالیک,پلی ال اکریلیک,واکس,سلولز استات بوتیرات}, url = {https://amnc.aut.ac.ir/article_119155.html}, eprint = {https://amnc.aut.ac.ir/article_119155_b0bd85c25611a9eaef902f8bfb5b47a4.pdf} } @article { author = {Taheri, Malihe and Sarabi, Ali Asghar and Roshan, Shamim}, title = {Synthesis of redox- responsive polyaniline microcapsules containing 8-hydroxyquinoline for corrosion protection of coatings.}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2502-2511}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.6}, abstract = {In this work, polyaniline (PANI) microcapsules were successfully synthesized by the oxidative polymerization in the direct mini-emulsion method. 8-hydroxyquinoline (8-HQ) was used as a corrosion inhibitor in the core of microcapsules, which can also act as a fluorescent indicator. The synthesized microcapsules were characterized by Field Emission Scanning Electron Microscopy (FE-SEM), Dynamic Light Scattering (DLS), Fourier Transform Infrared spectroscopy (FTIR), Thermal Gravimetric Analysis (TGA) and Ultraviolet-Visible spectroscopy (UV–Vis) techniques. The qualitative study of the corrosion resistance behavior of coatings containing microcapsules was performed using the salt spray test. The FE-SEM images were used to study the morphology of the surface of the microcapsules. According to FE-SEM images, the microcapsules with and without 8-HQ were almost identical in appearance, and the diameter of the spherical microcapsules was approximately 0.6-5 µm. The results of the DLS showed that the synthesized microcapsules are monodisperse and have a narrow distribution of particle size. The chemical structure of the microcapsules was investigated using FTIR spectroscopy. The results of the TGA analysis confirmed the formation of polyaniline microcapsules. The UV–Vis spectroscopy showed that polyaniline microcapsules are sensitive to reducing and oxidizing agents and are released by reduction-oxidation reactions. Since PANI microcapsules can exhibit an oxidation-reduction response to electrical or chemical stimuli, these particles could be an appropriate choice to be used in anti-corrosion and self-healing applications in metallic systems. The results of the salt spray test showed that the epoxy coating containing 5 wt.% of the microcapsules, has better corrosion resistance than the epoxy.}, keywords = {Polyaniline microcapsules,Self-healing,Fluorescent indicator,8-Hydroxyquinoline,Mini-emulsion}, title_fa = {سنتز میکروکپسول‌های پلی‌آنیلین حساس به واکنش کاهش- اکسایش محتوی بازدارنده ۸- هیدروکسی کوئینولین به‌منظور حفاظت پوشش‌ها در برابر خوردگی}, abstract_fa = {در پژوهش حاضر میکروکپسول‌های پلی‌آنیلین به روش پلیمریزاسیون اکسیداسیونی آنیلین در مینی‌امولسیون مستقیم تهیه شدند. از 8- هیدروکسی کوئینولین (8-HQ) به‌عنوان بازدارنده خوردگی در هسته میکروکپسول‌ها استفاده شد که می‌تواند به‌عنوان یک شناساگر فلورسنتی نیز عمل کند. شناسایی میکروکپسول‌های سنتز شده با استفاده از تصاویر میکروسکوپ الکترونی روبشی گسیل میدانی (FE-SEM)، آزمون تفرق نور پویا (DLS)، طیف‌سنجی مادون قرمز با تبدیل فوریه (FTIR)، آزمون توزین حرارتی (TGA) و طیف‌سنجی نور مرئی- فرابنفش (UV-Vis) انجام شد. بررسی کیفی رفتار مقاومت به خوردگی پوشش‌های حاوی میکروکپسول با استفاده از آزمون مه نمکی انجام شد. تصاویر FE-SEM برای بررسی سطح میکروکپسول‌ها مورد استفاده قرار گرفت. با توجه به تصاویر، شکل ظاهری میکروکپسول‌ها در حضور و عدم حضور 8-HQ تفاوت چندانی ندارند و میکروکپسول‌های سنتز شده، کروی شکل و با اندازه ۵-6/0 میکرومتر هستند. نتایج آزمون DLS، نشان داد که میکروکپسول‌های تهیه شده تک پراکنشی هستند و توزیع اندازه ذرات باریکی را دارند. ساختار شیمیایی میکروکپسول‌ها با استفاده از آزمون FTIR مورد بررسی قرار گرفت. نتایج آزمون TGA، شکل‌گیری میکروکپسول‌های پلی‌آنیلین را تأیید کرد. نتایج آزمون UV-Vis نشان داد که میکروکپسول‌های پلی‌آنیلین به عوامل کاهنده و اکسنده حساس هستند و با انجام واکنش‌های کاهش- اکسایش رهایش می‌یابند. از آنجا که میکروکپسول‌های PANI می‌توانند پاسخ کاهش- اکسایشی در برابر محرک‌های الکتریکی یا شیمیایی نشان دهند، این ذرات انتخاب مناسبی برای کاربردهای ضد خوردگی و خودترمیم شوندگی در سامانه‌های فلزی هستند. نتایج آزمون مه نمکی نشان داد که پوشش اپوکسی حاوی ۵ درصد وزنی میکروکپسول، مقاومت به خوردگی بهتری نسبت به پوشش اپوکسی دارد.}, keywords_fa = {میکروکپسول پلی‌آنیلین,خودترمیم شونده,شناساگر فلورسنتی,۸- هیدروکسی کوئینولین,مینی‌امولسیون}, url = {https://amnc.aut.ac.ir/article_119778.html}, eprint = {https://amnc.aut.ac.ir/article_119778_8a96a8002cf13f40404e24edaf0b361b.pdf} } @article { author = {Mosharafian, Masoumeh and Sadeghi, Mohammad and Massah, Ahmadreza}, title = {Synthesis and Electrical Conductivity Evaluation of Cross-linked Starch-Nanoclay Montmorillonite/Graphene Nanocomposite}, journal = {Advanced Materials and New Coatings}, volume = {9}, number = {34}, pages = {2512-2518}, year = {2020}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2020.9.34.7}, abstract = {In this paper, starch nanocomposite are synthesized by the addition of nanocrystalline montmorillonite and graphite and identified by various characterization methods. To improve the nanocomposite properties of starch, it is activated using methyl methamethacrylate monomer, and then polymer (methyl methacrylate) polymer is placed on the starch by polymerization reaction on starch. Methylene base-acrylamide mesh agent has been used to make cross-links in polymers and to cross-link them. The composite prepared in this study was identified by various methods, including nuclear magnetic resonance imaging, subcutaneous radiography, scanning electron microscopy imaging, and heat weight analysis. Graphite has been used as a conductive additive in composites and the electrical conductivity of composites has been evaluated by the spectroscopic method of electrochemical impedance. Different amounts of graphite, including 0, 5, 10 and 15% by weight of graphite, were used as additives in the composite, and an electrical conductivity study showed that a composite containing 10% by weight of graphite showed the highest conductivity. The results showed that the starch composite of the grid containing the monoclonal nanofluid additives and graphite had an electrical conductivity.}, keywords = {Conductive composite,cross linked starch,montmorillonite nanoclay,Graphite}, title_fa = {سنتز و بررسی رفتار هدایت الکتریکی کامپوزیت نشاسته شبکه‌ای شده حاوی افزودنی نانوکلی مونت‌موریلونیت و گرافیت}, abstract_fa = {در این مقاله نانوکامپوزیت نشاسته حاوی افزودنی نانوکلی مونت‌موریلونیت و گرافیت سنتز شده و با روش‌های مختلف مورد شناسایی قرار گرفته است. برای بهبود خواص نانوکامپوزیتف نشاسته با منومر متیل‌متاکریلات عامل‌دار شده و سپس با انجام واکنش پلیمریزاسون بر روی نشاسته، پلیمر پلی(متیل متاکریلات) بر روی نشاسته قرار گرفته است. عامل شبکه‌ساز متیلن بیس‌آکریل‌آمید برای ایجاد پیوندهای عرضی در پلیمر و شبکه‌ای کردن آن مورد استفاده قرار گرفته است. کامپوزیت تهیه شده در این تحقیق با روش‌های مختلف شامل پرتونگاری رزونانس مغناطیس هسته، پرتونگاری زیرقرمز، تصویربرداری میکرویکوپ الکترونی روبشی و آنالیز وزن‌سنجی حرارتی مورد شناسایی قرار گرفت. از گرافیت به عنوان افزودنی رسانا در کامپوزیت استفاده شده و رسانایی الکتریکی کامپوزیت با روش طیف‌سنجی امپدانس الکتروشیمیایی مورد ارزیابی قرار گرفته است. مقادیر مختلف گرافیت شامل 0، 5، 10 و 15 درصد وزنی گرافیت به عنوان افزودنی در کامپوزیت استفاده شده و بررسی رسانایی الکتریکی نشان داد که کامپوزیت حاوی 10 درصد وزنی گرافیت بیشترین رسانایی را نشان داده است. نایج به دست آمده نشان داد که کامپوزیت نشاسته شبکه‌ای حاوی افزودنی نانوکلی مونت موریلونیت و گرافیت دارای رسانایی الکتریکی می‌باشد.}, keywords_fa = {کامپوزیت زمینه پلیمری رسانا,نشاسته‌ی شبکه‌ای,نانوکلی مونت‌موریلونیت,گرافیت}, url = {https://amnc.aut.ac.ir/article_119779.html}, eprint = {https://amnc.aut.ac.ir/article_119779_2ebdd78bdfeca4c9ab18705817c3fc76.pdf} }