@article { author = {Nouri, Masoud and Bijani, Milad and Sarabi, Ali Asghar and Eivaz Mohammadloo, Hossein}, title = {Electrochemical properties and Morphology evaluation of the Lanthanum based Conversion Coating on Cold rolled steel}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {965-974}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.1}, abstract = {In this search, conversion coating was applied on cold rolled steel try immersing specimens in a solution including La(NO3)3, and the effect of immersion time has been investigated. Electrochemical properties of the formed oxide layer were assessed Electrochemical Impedance Spectroscopy (EIS) and DC Polarization measurements. The morphology of the surface of wild rolled steel treated by conversion coating at different immersion times was studied by Field Emission Scanning Electron Microscopy (FE-SIM). The EIS and SEM results showed that better corrosion resistance (2.5 kΩ.cm2) along with a more uniform surface profile was achieved after 5 min immersion in the conversion coating bath. On the other hand, the coatings, which were formed by immersion in the rare-earth salt containing solution, significantly reduced the dissolution of La oxides and deteriorated the substrate after 50 min. Adhesion of epoxy organic coating to the untreated and La conversion-coated CRS was evaluated try pull-off method and results revealed the positive performance of La conversion coating.}, keywords = {Conversion coating,Lanthanum Nitrate,polarization,Electrochemical Impedance Spectroscopy (EIS),Field Emission Scanning Electron Microscopy (FE-SEM)}, title_fa = {ارزیابی رفتار الکتروشیمیایی و ریخت شناسی پوشش تبدیلی بر پایه لانتانیم بر روی فولاد نورد سرد}, abstract_fa = {در این پژوهش، رفتار الکتروشیمیایی و ریخت شناسی پوشش تبدیلی بر پایه فلز کمیاب خاکی لانتانیم، با غوطه وری نمونه های فولاد نورد سرد در محلول لانتانیم نیترات و اعمال آن بر زیر آیند، بررسی شد و اثر زمان غوطه وری در محلول پوشش تبدیلی مورد ارزیابی قرارگرفت. مقاومت به خوردگی لایه اکسید تشکیل شده بر زیر ایند فولادی به کمک آزمون های قطبش و طیف سنجی امپدانس الکتروشیمیایی مورد مطالعه قرار گرفت. ریخت شناسی سطح پوشش تبدیلی توسط میکروسکوپ الکترونی روبشی گسیل میدانی ارزیابی شد. نتایج آزمون ها نشان داد که نمونه پوشش شده با زمان غوطه وری ۵دقیقه، مقاومت خوردگی بالاتر   (( 2/5 KΩ. Cm2و سطح یکنواخت تری را در مقایسه با دیگر نمونه ها دارد. همچنین، با افزایش زمان غوطه وری تا ۵۰ دقیقه مقاومت به خوردگی کاهش می یابد و پوشش تبدیلی تشکیل شده در محلول پوشش تبدیلی حل می شود و یکنواختی سطح پوشش کاهش می یابد. چسبندگی پوشش الی بر پایه اپوکسی بر روی زمینه فولادی اصلاح نشده و اصلاح شده با پوشش تبدیلی لانتانیمی توسط آزمون Pull off بررسی شد و نتایج بیانگر عملکرد مؤثر پوشش تبدیلی در بهبود چسبندگی بود.}, keywords_fa = {پوشش تبدیلی,لانتانیم نیترات,قطبش,طیف سنجی امپدانس الکتروشیمیایی,میکروسکوپ الکترونی روبشی,گسیل میدانی}, url = {https://amnc.aut.ac.ir/article_69132.html}, eprint = {} } @article { author = {Hedayati, Hamid Reza and Sabbagh Alvani, Ali Asghar and Sameie, Hassan and Moosakhani, Shima and Salimi, Reza and Tabatabaee, Farzaneh and Amiri Zarandi, Ali and Kiani, Sajjad}, title = {The Effect of Zn2+ Enrichment on the Cobalt Chromite Spinel Pigments: Synthesis, Characterization, Colorimetric and NIR Reflectance Properties}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {975-982}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.2}, abstract = {In the present study, Co1-X ZnX Cr2O4  nano-pigments have been successfully synthesized via polymeric precursor method. The phase analysis was carried out by X-ray diffraction (XRD) indicating that all the samples have cubic spinel structure. SEM images showed that the grains are homogeneously individualized with a particle size of between 100-200 nm. Furthermore, UV-Vis absorption spectra exhibited an intense broad band in the range of 500-700 nm, which could be related to 4A2(F)→4T1(P)    spin-allowed electronic transition of Co2+ ions in the tetrahedral position of spinel structure. On the bedrock of colorimetric properties and UV-Vis-NIR reflectance measurements, Zn2+. enrichment of spinel structure up to 75% resulted in enhancement of chroma and green hue as well as improvement of NIR solar reflectance. High NIR reflectance properties for these pigments clearly highlights the potential for the utility of these pigments in the cool coatings.}, keywords = {Near-infrared reflective pigments,Polymeric precursor method,Cool coatings,UV-Vis NIR spectrophotometry}, title_fa = {اثر حضور کاتیون روی در ساختار اسپینلی کبالت کرومیت: ساخت، مشخصه یابی، رنگ سنجی و خواص بازتابی فروسرخ}, abstract_fa = {در پژوهش حاضر، نانو رنگدانه های Co1-X ZnX Cr2O4 به روش پیش ساز پلیمری تهیه شده اند. را بررسی خواص فازی نمونه ها به کمک آزمون پراش اشعه ایکس نشان داد که نانورنگدانه های  تهیه شده دارای ساختار مکعبی اسپینل هستند. تصاویر حاصل از آزمون میکروسکوپ الکترونی روبشی نیز بیانگر شکل گیری ریزساختار منظم و یکنواخت ذرات با ابعادی در محدوده ۱۰۰ تا ۲۰۰ نانومتر بود. طیف جذبی به دست آمده به کمک دستگاه اسپکتروفوتومتر، نوار پهن شدیدی در محدوده ۵۰۰ تا ۷۰۰ نانومتر را نشان داد که می توان آن را به جهش های الکترونی 4A2(F)→4T1(P)مربوط به Co2+ در موقعیت چهار وجهی نسبت داد. همچنین، نتایج حاصل از طیف بازتابی UV - Vis -NIR و رنگ سنجی رنگدانه ها نشان داد، جایگزینی یون های کبالت با روی تا مقدار ۷۵ درصد در ساختار اسپینل، ضمن بهبود فام سبز و خلوص رنگدانه، سبب افزایش مقدار بازتاب فروسرخ می گردد. در انتها، طیف بازتابی نمونه ها در محدوده مرئی و فروسرخ نشان میدهد که این نموندها ضمن داشتن جذب نسبتاً بالا در ناحیه مرئی، بازتاب بالایی در ناحیه فروسرخ دارند، که آنها را به عنوان گزینه مناسبی جهت استفاده در پوششهای خنک مطرح می نماید.}, keywords_fa = {رنگدانه های بازتاب دهنده امواج فروسرخ نزدیک,روش پیش ساز پلیمری,پوشش های خنک,اسپکتروفوتومتری,UV - Vis –NIR}, url = {https://amnc.aut.ac.ir/article_69134.html}, eprint = {} } @article { author = {Sadeghi-Kiakhani, Mousa}, title = {Application of poly(amidoamine) dendrimer as a retarding agent in acrylic dyeing with a basic dye}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {983-990}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.3}, abstract = {Abstract In this article, poly(amidoamine) dendrimer (PAMAM) (G=-0.5) was tested as a dye retardant in the dyeing of acrylic fibers with a basic dye (C.1 Basic Blue 41: BB41). Factors affecting the rate of dyeing acrylic fibers with the basic dye, such as time and temperature, were studied in the presence of PAMAM. The results showed that the dyeing acrylic fibers with in the presence of PAMAM dendrimer have an acceptable uniformity compared to dodecyltrimethylammonium bromide (DTAB) as a cationic surfactant. It seems that the complex formation between the dendrimer and dye molecules might delay dyeing equilibrium time, and consequently, a uniform dyeing is obtained. The kinetics of acrylic fibers with a basic dye in the presence of PAMAM and DTAB was compared based on different empirical equations,parabolic, first-order, and modified Cegarra-Puente model. The modified Cegarra-Puente  model was in good agreement with the experimental data compared to the other models.}, keywords = {Dendrimer,Retarder: Surfactant,Dyeing: Acrylic fiber,Basic dye}, title_fa = {کاربرد دندریمر پلی آمیدوآمین به عنوان ریتاردر در رنگرزی الیاف اکریلیک با ماده رنگزای بازیک}, abstract_fa = {در این تحقیق، از دندریمر پلی امیدوآمین نسل منفی نیم (G=-0/5)به عنوان کند کننده سرعت رنگرزی - در فرایند رنگرزی الیاف آکریلیک با ماده رنگزای بازیک آبی ۴۱- استفاده شد. عوامل مؤثر بر سرعت رنگرزی الیاف اکریلیک با ماده رنگزای بازیک، از جمله زمان،دما و غلظت دندریمر، بررسی شدند. نتایج نشان داد که الیاف آکریلیک رنگرزی شده با ماده رنگزای بازیک در حضور دندریمر، در مقایسه با سطح فعال کاتیونی دودسیل ترى متیل آمونیوم بروماید ،از یکنواختی قابل قبولی برخوردار است. به نظر می رسد که با ایجاد کمپلکس بین مولکول های ماده رنگزا و دندریمر زمان تعادل در رنگرزی به تأخیر افتاده و در نتیجه رنگرزی یکنواخت تری حاصل می شود. همچنین، سینتیک رنگرزی الیاف اکریلیک با ماده رنگزای بازیک در حضور دندریمر و سطح فعال با استفاده از معادله های تجربی سهمی، مرتبه اول و مدل اصلاح شده سگارا-پونته مورد مقایسه قرار گرفت. نتایج نشان داد که سینتیک رنگرزی الیاف آکریلیک در حضور دندریمر و سطح فعال در شرایط مختلف تطابق قابل قبولی با معادله سگارا-پونته دارد.}, keywords_fa = {دندریمر,تاخیردهنده,سطح فعال,رنگرزی,الیاف آکریلیک,ماده رنگزای بازیک}, url = {https://amnc.aut.ac.ir/article_69135.html}, eprint = {} } @article { author = {Salimi, Sina and Zaarei, Davood and Fazaeli, Reza}, title = {Influences of Inorganic Coatings on Corrosion Resistance of Invar Alloy}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {991-998}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.4}, abstract = {Invar alloy (64% Fe & 36%Ni) has low coefficient of thermal expansion (CTE). Invar's CTE is the lowest of any metal. This alloy is Iron based, so it can be corroded and need protection from corrosive species. In this research, corrosion prevention of Invar by inorganic surface coatings was investigated. Protective influences of electroless nickel plating, electroless nickel/ zinc plating double layer, and zinc rich ethyl silicate coatings were studied. Electrochemical polarization test and Tafel extrapolation were used to characterize the corrosion behavior of each specimen. Results showed that the corrosion current density (icorr) of bare Invar was about 4.08 Aµ/cm2 and the electroless nickel coating could not decrease icorr of Invar, suitably. In addition, the specimen with electroless nickel/zinc coating showed low icorr about 5.30*10-2 Aµ/ cm2. Also, with zinc rich ethyl silicate, the corrosion protection mechanism was cathodic and after 20 days, it changed to barrier mechanism with icorr about 6.71x10-2Aµ/cm2 in icorrin 3.5% wt sodium chloride solution.}, keywords = {Invar,corrosion,Polarization Test,Zinc rich ethyl silicate}, title_fa = {بررسی تاثیر پوشش های معدنی بر مقاومت خوردگی آلیاژ اینوار}, abstract_fa = {آلیاژ پیشرفته اینوار با ٪۶۴ آهن و ۳۶ نیکل کمترین ضریب انبساط حرارتی را در بین فلزات  داراست. این فلز دارای پایه آهنی بوده و مستعد خوردگی در محیط های مختلف است. در این تحقیق ، تأثیر سه نوع پوشش معلنی مشتمل بر نیکل غیر الکتریکی، دولایه نیکل غیر الکتریکی/روی و همچنین پوشرنگ اتیل سیلیکات غنی از روی بر کاهش چگالی جریان خوردگی اینوار بررسی شد. آزمون الکتروشیمیایی قطبش و برون یابی تافل به منظور سنجش و مقایسه رفتار خوردگی به کار رفت. نتایج به دست آمده مشخص نمود که چگالی جریان خوردگی اینوار تقریبا برابر با 4/08 Aµ/cm2است و پوشش نیکل غیر الکتریکی اعمالی بر سطح آن، کاهش قابل قبولی در چگالی جریان خوردگی به وجود نمی آورد. همچنین نمونه ی دارای پوشش دولایه نیکل غیر الکتریکی/روی چگالی جریان خوردگی پایین و کم تغییری در حدود 5/3 ×2-10 Aµ/cm2دارد، که نشان دهنده قابلیت حفاظتی آن است. به علاوه، پوشرنگ اتیل سیلیکات غنی از روی بر اینوار می تواند تا بیست روز در محلول 5/3% کلرید سدیم به صورت حفاظت کاتدی و پس از آن به شکل حفاظت سد کنندگی با کمینه چگالی خوردگی Aµ/cm210-2 ×  6/71 این آلیاژ را محافظت کند.}, keywords_fa = {اینوار,خوردگی,پوشش,آزمون قطبش,اتیل سیلیکات غنی از روی}, url = {https://amnc.aut.ac.ir/article_69136.html}, eprint = {} } @article { author = {Jalili, Mojtaba}, title = {Studying the effects of Rheological additives on the Rheological Properties of Offset Inks}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {999-1004}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.5}, abstract = {In this paper, the effects of three different additives with trade names of claytone AF, aerosol R972 and socal 312 on rheological properties of cold-set offset printing inks has been investigated. These additives have planar, spherical and cubic morphologies and they were treated by quaternary ammonium salts, Dichlorodimethylsilane and stearic acid, respectively. Effect of Additive weight percent (2,4 and 6 wt%) on theological properties like yield value, thixotropy, zero shear viscosity, and infinite shear viscosity was studied. The flow diagrams showed that zero shear viscosity. yield value and thixotropy increased with the increasing of weight percent of additives. In particular, it has been shown that claytone AF and socal 312 have the most and least effects on the aforementioned properties, respectively.}, keywords = {Ink,Offset printing,Rheology,Rheological additives,Thixotropy}, title_fa = {مطالعه تاثیر افزودنی های رئولوژیکی بر خواص رئولوژیکی مرکب های چاپ افست}, abstract_fa = {در این مقاله، تاثیر سه نوع افزودنی با نام های تجاری claytone AF, aerosil R972و  socal 312 بر خواص رئولوژیکی مرکب چاپ افست خشک شده به روش نفوذی بررسی و مقایسه شده است. این افزودنی ها به ترتیب دارای ریخت صفحه ای، کروی و مکعبی و آمایش شده با نمکهای آمونیم چهارگانه، دی کلرودی متیل سیلان و اسید استئاریک هستند. تاثیر این افزودنی ها در سه درصد وزنی ۲، ۴ و ۶ بر خصوصیات رئولوژیکی مانند عدد ماند، میزان تیکسوتروپی و گرانروی در سرعت های برشی نزدیک به صفر و بینهایت مطالعه شده است. نمودارهای جریان پذیری نشان داده اند که با افزایش درصد وزنی افزودنی ها، گرانروی در سرعت برشی نزدیک به صفر، عدد ماند و تیکسوتروپی همگی افزایش یافتند. به طور ویژه، claytone AF و 312Socalبه ترتیب بیشترین و کمترین اثر را بر خواص ذکر شده نشان داده اند.}, keywords_fa = {مرکب,چاپ افست,رئولوژی,افزودنی های رئولوژیکی,تیکسوتروپی}, url = {https://amnc.aut.ac.ir/article_69137.html}, eprint = {} } @article { author = {Mazaheri, Hossein and fazel, Mahmoud and Alaei, Alireza}, title = {Formation of Composite Layer Containing Silicon Carbide particles on the A106 Steel Surface by Tungsten Inert Gas (TIG)}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {1005-1014}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.6}, abstract = {In this study, formation of composite coatings containing silicon carbide particles on the ASTM A106-Gr.B steel surface via gas tungsten arc welding process was investigated. For this purpose, silicon carbide particles with different volume percent were applied on the steel surface and melt mixing process with the base metal was completed altering the current density. Study of microstructure of coatings was performed by optical microscopy and scanning electron microscope ,along with point analysis. The results of the measurements showed that coating had a dendritic structure containing silicon carbide reinforcement that can improve the hardness and the wear behavior of the mentioned coating. Hardness of the coating microhardness tests  and wear behavior of coatings was evaluated by the reciprocating wear test. Micro hardness test results were indicative of increasing of hardness of coated samples(of about 650 to 1200 vickers)compared to the uncoated sample(of about 200 vickers)Assessment of wear behavior of coatings revealed a significant improvement in wear behavior of the coatings upon addition of silicon carbide reinforcing agent. The main wear mechanism of the uncoated samples was delamination, and wear and surface oxidation, while for the coated samples was delamination,wear and surface oxidation,and adhesive wear.}, keywords = {Gas tungsten arc welding,Coating surface,Steel/silicon carbide composite}, title_fa = {ایجاد لایه کامپوزیتی حاوی ذرات کاربید سیلیسیوم بر سطح فولاد A106 با استفاده از قوس تنگستن- گاز}, abstract_fa = {در این پژوهش، ایجاد پوشش کامپوزیتی حاوی ذرات کاربید سیلیسیوم بر سطح فولاد   ASTM A106- Gr.B با به کارگیری فرآیند جوشکاری قوسی تنگستن/گاز بررسی شد. بدین منظور، ذرات کاربید سیلیسیوم با درصدهای حجمی متفاوت بر سلح فولاد مورد نظر پیش نشانی شد و با تغییر شدت جریان، فرآیند ذوب و اختلاط آنها با فلز پایه انجام گردید. مطالعه ریز ساختار پوشش ایجاد شده توسط میکروسکوپ نوری و میکروسکوپ الکترونی روبشی همراه با تحلیل نقطه ای انجام گرفت. یافته های آزمون ها نشان داد که پوشش حاصله ساختاری دندانه ای دارد که حاوی تقویت کننده کاربید سیلیسیوم است و می تواند سبب بهبود سختی و رفتار سایشی پوشش مذکور شود. سختی پوشش ها در آزمون های ریز سختی سنجی و رفتار سایشی پوشش ها توسط آزمون سایش به صورت رفت و برگشتی ارزیابی شد. نتایج آزمون ریز سختی سنجی نشان دهنده افزایش سختی پوشش ایجاد شده (حدود ۶۵۰ تا ۱۲۰۰ ویکرز) نسبت به نمونه بدون پوشش (حدود ۲۰۰ ویکرز) بود. بررسی رفتار سایشی پوشش ها بیانگر بهبود چشمگیر رفتار سایشی آنها در اثر افزودن تقویت کننده کاربید سیلیسیوم بود. سازوکار عمده ی سایش در نمونه ی بدون پوشش سایش ورقه ای و اکسایش سطحی و در نمونه های پوشش داده شده تلفیقی از سایش ورقه ای، اکسایش سطحی و سایش چسبان تشخیص داده شد.}, keywords_fa = {جوشکاری قوسی تنگستن/گاز,پوشش دهی سطحی,کامپوزیت فولاد/کاربید سیلسیوم}, url = {https://amnc.aut.ac.ir/article_69138.html}, eprint = {} } @article { author = {Maddah, Bozorgmelir and Fakhrali, Aref}, title = {Synthesis and Characterization of Polyacrylamideoxime and Its Nanofibers as Self-Decontamination Coatings}, journal = {Advanced Materials and New Coatings}, volume = {4}, number = {14}, pages = {1015-1022}, year = {2014}, publisher = {}, issn = {2322-1356}, eissn = {}, doi = {/amnc.2015.4.14.7}, abstract = {In this study, the polyacryliamodoxime (PAAO) powder was synthesized by treating the polyacrylonitrile (PAN) powder through chemical procedures, and used to hydrolyze the simulated nerve agent, i.e., dimethoate. GC-MS spectroscopy technique demonstrated the ability of PAAO powder to hydrolysis over 95% of dimethoate pesticide within 12 hours. Since the properties of substances in nano scale are improved, it was planned to synthesize PAAO nano fibers via two methods: (i) conversion of PAN powder to PAAO powder and preparing its nanofiber, (ii) preparation of PAAO nanofibers from PAN nanofibers. Successful operation of the amidoximation was confirmed by FTIR technique. Thermal behavior of PAN and PAAO powders were investigated by thermogravimetric analyzer (TGA). SEM technique was used to study the morphology of PAAO nanofibers. SEM images revealed that PAAO nanofibers is uniform and Bead-less, hence, it could be used as a coating for self-decontamination procedure.}, keywords = {Nanofibers,Polyacrylamideoxime,Decontamination Coatings,Electrospinning,Polyacrylonitrile}, title_fa = {سنتز و شناسایی پلی اکریل آمیدوکسیم و تولید نانوالیاف از آن برای تهیه پوشش های خود آلودگی زدا}, abstract_fa = {در این پژوهش، ابتدا پودر پلی اکریل آمینوکسیم با انجام عملیات شیمیایی روی پودر پلی اکریلونیتریل تهیه گردید و سپس به منظور تخریب شبه عامل عصبی دیمتوات از طریق هیدرولیز مورد استفاده قرار گرفت. نتایج حاصل از کروماتوگرافی گازی اسپکترومتری جرمی جهت ارزیابی کارایی پودر پلی اکریل آمیدوکسیم نشان داد که پس از گذشت ۱۲ ساعته بیش از %95 از سم دیمتوات هیدرولیز شده است. از آنجا که خواص مواد در مقیاس نانو بهبود می یابد لذا امکان سنجی تولید نانو الیاف پلی اکریل آمیدوکسیم با دو روش تهیه پودر پلی اکریل آمیدوکسیم از پودر پلی اکریلونیتریل و تولید نانو الیاف از آن و تبدیل نانو الیاف پلی اکریلونیتریل به نانو الیاف پلی اکریل آمیدوکسیم انجام شد. موفقیت آمیز بودن عملیات آمیدوکسیم دار کردن با تبدیل فوریه مادون قرمز تأیید شد. همچنین، بررسی رفتار حرارتی پودر پلی اکریل آمیدوکسیم با دستگاه تحلیل حرارتی انجام گرفت. برای مطالعه ساختار نانو الیاف پلی اکریل آمیدوکسیم از میکروسکوپ الکترونی روبشی استفاده شد. میکرو عکس های گرفته شده نشان داد که نانو الیاف تولیدی به صورت یکنواخت و بدون دانه تسبیحی بوده و لذا می تواند به عنوان پوشش خود آلودگی زدا مورد استفاده قرار گیرد.}, keywords_fa = {نانوالیاف,پلی اکریل آمیدوکسیم,پوششش خود آلودگی زدا,الکتروریسی,پلی اکریلونیتریل}, url = {https://amnc.aut.ac.ir/article_69139.html}, eprint = {} }