Investigation of Morphology, Electrical and Electrochemical Properties of Gold Coating on Metallic Bipolar Plates of Fuel Cells

Document Type : Research Article

Authors

1 MalekAshtar University

2 Department of Materials Engineering, Shiraz University of Technology, Shiraz

3 Fuel Cell Technology Research Laboratory, Malek Ashtar University of Technology, Fereydunkenar

/amnc.2020.8.32.5

Abstract

Polymer electrolyte membrane fuel cells have received more attention than other fuel cells because of their advantages such as low operating temperature, high power density and short startup time. One of the most important components of a polymer electrolyte membrane fuel cell is bipolar plate which has various types. Metallic bipolar plates have advantages such as higher strength, lower thickness and lower weight than graphite-based composite bipolar plates. Corrosion resistance and interfacial contact resistance of metallic bipolar plates are some of the challenges of using metallic bipolar plates. For this reason, metallic bipolar plates are coated to increase corrosion resistance and reduce contact resistance. In this study, the properties and morphologies of gold coating on copper and stainless steel substrates were studied by using electroplating and sputtering methods. The surface morphologies of the specimens were investigated by scanning electron microscopy. In addition, interfacial contact resistance tests were used to evaluate contact resistance of coated and uncoated specimens. Finally, corrosion resistances of the specimens were studied using galvanostatic and potentiostatic tests. The results showed that the use of electroplating method produces many holes and pores in the specimen surface. It was also found that using sputtering method significantly resulted in an increase in corrosion resistance and decrease in contact resistance of coated specimens.

Keywords

References

[1] Wang, Y. and D.O. Northwood, An investigation into polypyrrole-coated 316L stainless steel as a bipolar plate material for PEM fuel cells. Journal of Power Sources, 2006. 163(1): p. 500-508.
[2] Wang, H. and J. Turner, Reviewing metallic PEMFC bipolar plates. Fuel Cells, 2010. 10(4): p. 510-519.
[3] Wang, Y. and D.O. Northwood, An investigation into TiN-coated 316L stainless steel as a bipolar plate material for PEM fuel cells. Journal of Power Sources, 2007. 165(1): p. 293-298.
[4] Taherian, R., A review of composite and metallic bipolar plates in proton exchange membrane fuel cell: Materials, fabrication, and material selection. Journal of Power Sources, 2014. 265: p. 370-390.
[5] Wind, J., R. Späh, W. Kaiser, and G. Böhm, Metallic bipolar plates for PEM fuel cells. Journal of Power Sources, 2002. 105(2): p. 256-260.
[6] Kumar, A., M. Ricketts, and S. Hirano, Ex situ evaluation of nanometer range gold coating on stainless steel substrate for automotive polymer electrolyte membrane fuel cell bipolar plate. Journal of Power Sources, 2010. 195(5): p. 1401-1407.
[7] Miyazawa, A., E. Tada, and A. Nishikata, Influence of corrosion of SS316L bipolar plate on PEFC performance. Journal of Power Sources, 2013. 231: p. 226-233.
[8] Davies, D., P. Adcock, M. Turpin, and S. Rowen, Bipolar plate materials for solid polymer fuel cells. Journal of Applied Electrochemistry, 2000. 30(1): p. 101-105.
[9] Yun, Y.-H., Deposition of gold–titanium and gold–nickel coatings on electropolished 316L stainless steel bipolar plates for proton exchange membrane fuel cells. international journal of hydrogen energy, 2010. 35(4): p. 1713-1718.
[10] Yan, W.-M., C.-Y. Chen, and C.-H. Liang, Comparison of performance degradation of high temperature PEM fuel cells with different bipolar plates. Energy, 2019. 186: p. 115836.
[11] بهرامی‌پور، م., س.م. ربیعی و م. جعفریان, بررسی خواص و مورفولوژی پوشش‌ نانولایه طلا ایجاد شده بر روی صفحات دوقطبی در پیل سوختی به روش اسپاترینگ. نانومواد, 2014. 4(12): p. 259-267.
[12] Joseph, S., J.C. McClure, R. Chianelli, P. Pich, and P. Sebastian, Conducting polymer-coated stainless steel bipolar plates for proton exchange membrane fuel cells (PEMFC). International Journal of Hydrogen Energy, 2005. 30(12): p. 1339-1344.
[13] Feng, K., Z. Li, H. Sun, L. Yu, X. Cai, Y. Wu, and P.K. Chu, C/CrN multilayer coating for polymer electrolyte membrane fuel cell metallic bipolar plates. Journal of Power Sources, 2013. 222: p. 351-358.
[14] Oyarce, A., N. Holmström, A. Bodén, S. Randström, and G. Lindbergh, In-situ Measurements of Contact Resistance and In-situ Durability studies of Steels and Coatings to be used as Bipolar Plates in PEMFCs. ECS Transactions, 2009. 25(1): p. 1791-1801.
[15] Ruset, C., E. Grigore, G. Collins, K. Short, F. Rossi, N. Gibson, H. Dong, and T. Bell, Characteristics of the Ti2N layer produced by an ion assisted deposition method. Surface and Coatings Technology, 2003. 174: p. 698-703.
[16] Park, J.H., D. Byun, and J.K. Lee, Employment of fluorine doped zinc tin oxide (ZnSnOx: F) coating layer on stainless steel 316 for a bipolar plate for PEMFC. Materials Chemistry and Physics, 2011. 128(1-2): p. 39-43.
[17] Lee, S.-J., C.-H. Huang, and Y.-P. Chen, Investigation of PVD coating on corrosion resistance of metallic bipolar plates in PEM fuel cell. Journal of materials processing technology, 2003. 140(1-3): p. 688-693.
[18] Yi, P., W. Zhang, F. Bi, L. Peng, and X. Lai, Enhanced corrosion resistance and interfacial conductivity of TiC x/aC nanolayered coatings via synergy of substrate bias voltage for bipolar plates applications in PEMFCs. ACS applied materials & interfaces, 2018. 10(22): p. 19087-19096.
[19] Yi, P., L. Zhu, C. Dong, and K. Xiao, Corrosion and interfacial contact resistance of 316L stainless steel coated with magnetron sputtered ZrN and TiN in the simulated cathodic environment of a proton-exchange membrane fuel cell. Surface and Coatings Technology, 2019. 363: p. 198-202.
[20] Yoon, W., X. Huang, P. Fazzino, K.L. Reifsnider, and M.A. Akkaoui, Evaluation of coated metallic bipolar plates for polymer electrolyte membrane fuel cells. Journal of Power Sources, 2008. 179(1): p. 265-273.

Files

Share

How to cite

Statistics